1 Pc Rectangular RFID Card
100 in stock
- Public transportation
- Access control
- Event Ticketing
- Gaming & identity
- Contactless transmission of data and supply energy (no battery needed)
₹ 12.00 ₹ 99.00
100 in stock
This is a 125kHz And 13.56MHz RFID Card used for Contactless transmission of data and supplies energy with no battery needed. Its Operating distance is Up to 100mm depending on antenna geometry. The operating frequency is 125kHz And 13.56MHz and the Data transfer speed is 106 kbit/s.
It is featured with Data integrity of 16 Bit CRC, parity, bit coding bit counting which allows Anti-collision. These cards are typically used in ticketing transactions: <100 ms including backup management.
Based on 0 reviews
Be the first to review “1 Pc Rectangular RFID Card”
Related products
-
Robotics and Science Kits, Sensors And Modules
1 Pc Sim 800L GSM – GPRS Module is low cost, low form factor GSM module based on Simcoms SIM800L chipset. Sim800L module supports quad-band GSM and GPRS network
Robotics and Science Kits, Sensors And Modules1 Pc Sim 800L GSM – GPRS Module is low cost, low form factor GSM module based on Simcoms SIM800L chipset. Sim800L module supports quad-band GSM and GPRS network
- GSM (Global System for Mobile Communications) and GPRS (General Packet Radio Service) technologies
- Quad-band operation for compatibility across multiple GSM frequency bands
- Supports making and receiving phone calls
- Enables sending and receiving SMS messages
- TCP/IP and HTTP support for internet connectivity
- SIM card slot for standard SIM card insertion
- Controlled using AT commands
- Interface via UART (Universal Asynchronous Receiver/Transmitter)
SKU: 1 Pc Sim 800L GSM - GPRS Module -
DIY Arduino Project Kit, Robotics and Science Kits
2 Wheel Arduino Nano Bluetooth Controlled Smart Robot Car Kit with HC-05 Bluetooth Module, L293D Motor Driver Module Connect with your Phone
DIY Arduino Project Kit, Robotics and Science Kits2 Wheel Arduino Nano Bluetooth Controlled Smart Robot Car Kit with HC-05 Bluetooth Module, L293D Motor Driver Module Connect with your Phone
Ready to Use Projects are available.
This Project Kit is not Returnable and Exchangeable.
Buy Now Bluetooth Robot Ready To Use Car At 1499/-
Bluetooth Control Robot Car Kit –
20 Pcs Jumper Wire Male To Male
20 Pcs Jumper Wire Male To Female
1 Pc Arduino Nano
1 Pc Yellow Chassis
2 Pcs BO Small Wheel
2 Pcs BO Motor
1 Pc HC-05 Bluetooth Module
2 Pcs 9v battery and Connector
1 Pc 400 Points Breadboard
1 Pc L298N Motor Driver Module
1 Pc Caster Wheel
2 Pcs 7805 IC
4 Pcs Cable TieSKU: Bluetooth Control Arduino Nano Robot Car -
Robotics and Science Kits
1 Set IR Sensor 3 Pin Module with Single Channel Relay Module and Female To Female Jumper Wire for Arduino 1 Channel Relay Module for DIY for sanitizer kits and Electronic Projects
Robotics and Science Kits1 Set IR Sensor 3 Pin Module with Single Channel Relay Module and Female To Female Jumper Wire for Arduino 1 Channel Relay Module for DIY for sanitizer kits and Electronic Projects
IR Sensor 3 Pin Module:
- Infrared sensing technology for object detection.
- 3-pin configuration (VCC, GND, OUT).
- VCC connects to the power supply (e.g., 5V).
Single Channel Relay Module:
- Relay for electrically controlled switching.
- Single channel for controlling one device or circuit.
- Enables the Arduino to control high-voltage circuits.
Female To Female Jumper Wire:
- Designed to bridge connections between components on breadboards or platforms.
- Used for temporary or semi-permanent connections between electronic components.
- Female connectors easily slide onto and grip male header pins.
SKU: 1 Set IR Sensor+Relay with Jumper Wire -
Robotics and Science Kits, Sensors And Modules
DHT11 Temperature and Humidity Sensor with Accurate Temperature and Humidity Monitoring Ideal for Home Automation, Weather Stations, and HVAC Systems
Robotics and Science Kits, Sensors And ModulesDHT11 Temperature and Humidity Sensor with Accurate Temperature and Humidity Monitoring Ideal for Home Automation, Weather Stations, and HVAC Systems
- Uses a resistive humidity measurement component and a thermistor for temperature
- Converts variations in resistance into digital values for temperature and humidity
- Utilizes a simple, single-wire digital interface
- Provides digital signal output using a specific communication protocol
- Operates at 3.3V or 5V DC
- Low power consumption, suitable for energy-efficient applications
- Compact size with three pins: VCC, GND, and DATA
- Easy interfacing with popular microcontrollers like Arduino, Raspberry Pi, etc
- Used in weather stations, indoor climate monitoring, HVAC systems, agriculture, and more
- Provides essential data for temperature and humidity-sensitive applications
SKU: 1 Pc DHT11 Temperature and Humidity Sensor
There are no reviews yet.